Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
We have uncovered this post pertaining to Tools You Need to Install a New Bathtub listed below on the net and decided it made good sense to write about it with you over here.
Installing a tub isn't exactly rocket science, but it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably tough task. If the old tub is easily obtainable, the task can relocate rapidly; if you have to open a wall to remove the old bathtub and also place the new tub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will need a helper to move out the old bathtub and embeded in the brand-new one. Make certain you have certified yourself for the job and also fit attempting it. Rather than working with a contractor to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Chances are you may need a specialist plumber to make tube links.
This write-up will aid you mount a new tub in your shower room if you have already purchased a brand-new bathtub and also don't need to change the arrangement of your previous water system pipelines.
Your devices and also product list must consist of the following:
Planning for the Setup
First of all, the sustaining frame supplied with the bath must be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent strain on the bathtub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be quite problematic due to the restricted gain access to that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the faucets. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipes have been eliminated, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing substance.
Prior to moving on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, position the bath tub in the called for setting. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The next goal is to ensure that the tub is leveled all round. This can be achieved by checking the spirit level as well as adjusting the feet on the tub up until the spirit level reviews degree.
To install faucets, fit all-time low of the outermost adaptable faucet adapter to the suitable supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Turn on the water system and check all joints and also new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as also examine the overflow outlet and the normal electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the tub has actually been made use of at least once as this will settle it right into its final placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making sure that the washers are in area between the tap and also the sink. Safeguard the tap in place with the supplier supplied backnut. When the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The previous kind ought to be attached to the faucet ends first, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, creating the water to pass through the wall surface between the bath and also the tiling, causing issues with dampness and also possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and cartridges, and can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can fracture rather early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that piece of content was really useful. Loved our posting? Please share it. Help others discover it. Many thanks for your time invested reading it.
Act fast, Call us! Report this page